Maxus Deliver 7 brake replacement requires the correct genuine parts – replacing the brake pads and discs is straightforward, but ordering the correct components is where most owners get caught out. The Deliver 7 has had running changes across production years, and your VIN or registration number determines exactly which brake components fit your van.

Key Facts – Deliver 7 Brake Replacement

  • Front brakes: Ventilated discs with single-piston sliding calipers
  • Rear brakes: Solid discs (not drums) on most variants
  • Parts needed: Pads, discs, and potentially wear sensors depending on variant
  • Fitment varies: Your VIN/registration determines the exact part numbers – “Deliver 7” alone is not enough to confirm fitment
  • Genuine SAIC Maxus parts: OEM specification, confirmed against your vehicle before dispatch

Why the Right Part Number Matters on the Deliver 7

Many owners assume that knowing they drive a Deliver 7 is enough to order brake parts. It is not. SAIC has made specification changes across the Deliver 7 range, and brake disc diameters, pad shapes, and mounting points can differ between chassis numbers. A set of front pads for one Deliver 7 may not be the same as another built six months later.

This is a common issue across the Maxus range – and it catches owners of Deliver 3, Deliver 5, and Deliver 9 vans the same way. The simplest way to avoid ordering the wrong parts is to look up your van by registration number or VIN before you buy.

We confirm fitment against your specific vehicle before we dispatch any parts. That means no guesswork and no returns for wrong fitment.

What You Need for a Full Brake Service

A standard Deliver 7 brake replacement typically involves:

  • Brake pads (front and/or rear): Genuine SAIC Maxus pads are designed for the weight and braking characteristics of a loaded van. Pattern parts often fade under heavy loads or repeated braking.
  • Brake discs: Front discs are ventilated. If your discs are lipped, scored, or below minimum thickness, they should be replaced at the same time as the pads.
  • Brake wear sensors: Some Deliver 7 variants use electronic wear sensors. If yours does, replace the sensor each time you fit new pads.
  • Caliper slider pins and boots: Worth inspecting during any brake job. Seized sliders cause uneven pad wear and can ruin new pads quickly.

We stock all of these as genuine SAIC Maxus components from our catalogue of over 43,000 OEM parts.

Maxus Deliver 7 Brake Replacement: Step-by-Step Guide

This is a general overview. Always follow the SAIC workshop manual for torque specifications and procedures specific to your variant.

  1. Preparation: Chock the rear wheels, loosen the front wheel bolts, and raise the van on axle stands. Never work under a van supported only by a jack.
  2. Remove the caliper: Undo the caliper slider bolts and lift the caliper off the disc. Support it with a wire hook – do not let it hang by the brake hose.
  3. Remove old pads and disc: Slide the old pads out. If replacing discs, remove the caliper bracket bolts and then the disc. A few taps with a rubber mallet may free a corroded disc.
  4. Fit new disc: Clean the hub face of rust and debris. Fit the new disc and reattach the caliper bracket to the correct torque.
  5. Fit new pads: Push the caliper piston back using a proper wind-back tool (rear pistons on some vans may need rotating, not just pushing). Fit the new pads, replace the wear sensor if applicable, and refit the caliper.
  6. Bed in: After refitting the wheels and lowering the van, pump the brake pedal several times before driving. Bed in the new pads gently over the first few hundred miles – avoid heavy braking where possible.

Genuine vs Pattern Brake Parts

We only sell genuine SAIC Maxus parts. For brake components, this matters more than most people realise. Maxus vans are working vehicles – they carry heavy loads, brake repeatedly in urban deliveries, and need consistent stopping power. Genuine pads use the friction material specified by SAIC for the Deliver 7’s weight and braking system. Cheap pattern pads may look similar but can fade under load, wear unevenly, or cause disc damage.

If you run a fleet, our trade account gives you access to trade pricing across the full parts range.

Frequently Asked Questions

How do I know which brake pads fit my Deliver 7?

Use our VIN lookup tool to identify the exact OEM part numbers for your van. Simply knowing you have a Deliver 7 is not enough – your chassis number determines which parts fit. We confirm fitment before dispatch so you will not receive the wrong components.

Should I replace discs and pads at the same time?

Not always. If your discs are above minimum thickness, evenly worn, and free of deep scoring or cracks, fitting new pads alone is fine. However, if the discs are lipped or below specification, fitting new pads on worn discs will shorten pad life and may cause vibration under braking.

Can an independent garage fit genuine Maxus brake parts?

Yes. Any competent garage can fit genuine SAIC Maxus brake components. There is no requirement to use a franchised dealer. The parts are the same OEM components – we just supply them directly. Many independent garages and mobile mechanics order from us regularly.

How long do Deliver 7 brake pads typically last?

It depends entirely on how the van is used. A lightly loaded Deliver 7 covering motorway miles may see front pads last well beyond 30,000 miles. A fully laden van doing constant stop-start urban deliveries may need new fronts at half that. Rear pads generally last longer than fronts. Check pad thickness at every service interval.

Do you deliver brake parts UK-wide?

Yes. We dispatch via FedEx across the UK. You can check delivery details on our shipping information page.

If you need brake pads, discs, or any other genuine Maxus parts for your Deliver 7, enter your registration or VIN on our site and we will confirm the correct parts for your vehicle. For fleet or trade orders, get in touch for account pricing.